-
Notifications
You must be signed in to change notification settings - Fork 0
/
commands-wds.h
54 lines (50 loc) · 3.02 KB
/
commands-wds.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
/*
* uqmi -- tiny QMI support implementation
*
* Copyright (C) 2014-2015 Felix Fietkau <[email protected]>
*
* This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU Lesser General Public
* License as published by the Free Software Foundation; either
* version 2 of the License, or (at your option) any later version.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* Lesser General Public License for more details.
*
* You should have received a copy of the GNU Lesser General Public
* License along with this library; if not, write to the
* Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor,
* Boston, MA 02110-1301 USA.
*/
#define __uqmi_wds_commands \
__uqmi_command(wds_start_network, start-network, no, QMI_SERVICE_WDS), \
__uqmi_command(wds_set_apn, apn, required, CMD_TYPE_OPTION), \
__uqmi_command(wds_set_auth, auth-type, required, CMD_TYPE_OPTION), \
__uqmi_command(wds_set_username, username, required, CMD_TYPE_OPTION), \
__uqmi_command(wds_set_password, password, required, CMD_TYPE_OPTION), \
__uqmi_command(wds_set_ip_family_pref, ip-family, required, CMD_TYPE_OPTION), \
__uqmi_command(wds_set_autoconnect, autoconnect, no, CMD_TYPE_OPTION), \
__uqmi_command(wds_set_profile, profile, required, CMD_TYPE_OPTION), \
__uqmi_command(wds_stop_network, stop-network, required, QMI_SERVICE_WDS), \
__uqmi_command(wds_get_packet_service_status, get-data-status, no, QMI_SERVICE_WDS), \
__uqmi_command(wds_set_ip_family, set-ip-family, required, QMI_SERVICE_WDS), \
__uqmi_command(wds_set_autoconnect_setting, set-autoconnect, required, QMI_SERVICE_WDS), \
__uqmi_command(wds_reset, reset-wds, no, QMI_SERVICE_WDS), \
__uqmi_command(wds_get_current_settings, get-current-settings, no, QMI_SERVICE_WDS) \
#define wds_helptext \
" --start-network: Start network connection (use with options below)\n" \
" --apn <apn>: Use APN\n" \
" --auth-type pap|chap|both|none: Use network authentication type\n" \
" --username <name>: Use network username\n" \
" --password <password>: Use network password\n" \
" --ip-family <family>: Use ip-family for the connection (ipv4, ipv6, unspecified)\n" \
" --autoconnect: Enable automatic connect/reconnect\n" \
" --profile <index>: Use connection profile\n" \
" --stop-network <pdh>: Stop network connection (use with option below)\n" \
" --autoconnect: Disable automatic connect/reconnect\n" \
" --get-data-status: Get current data access status\n" \
" --set-ip-family <val>: Set ip-family (ipv4, ipv6, unspecified)\n" \
" --set-autoconnect <val>: Set automatic connect/reconnect (disabled, enabled, paused)\n" \
" --get-current-settings: Get current connection settings\n" \